Material to repair pants, jackets, gloves

Various topics, technical questions, announcements, events, resorts, ...

Moderators: fivat, rilliet, Arnaud, nils

User avatar
voodoo
Rank 4
Rank 4
Posts: 69
Joined: Tuesday 5 December 2006, 15:28
Location: sLOVEenia

Post by voodoo » Wednesday 28 February 2007, 12:47

jfamin wrote:For my gloves I used specific plastic beads (the one that melts easily in boiling water for different repairs) and apply it on finger tips and palm.
It's very resistant and slides very well on snow.
Jean Paul
i use for my gloves Shoe Goo...it is easy to put it on gloves and
they are realy good...

http://www.overboardenterprises.com/ima ... oe_goo.jpg
boards:Swoard 175 H, Sigi Grabner Speed GS 185
bindings: F2 Race titanium, INTEC TITANFLEX
Boots: Deeluxe Indy+BTS,

User avatar
The Blitz
Rank 5
Rank 5
Posts: 1532
Joined: Friday 4 October 2002, 13:59
Location: IdF | 91
Contact:

Post by The Blitz » Wednesday 28 February 2007, 15:50

Yeah...Shoe Goo!
I would like to find it in France for my hockey skate, but unfortunately Shoe Goo is banned (toxic ?) :?
 - 168XH Pro - Custom Dual 168H - Swallow Undertakeur 185

-- Tignes 19 au 25 mars --

User avatar
voodoo
Rank 4
Rank 4
Posts: 69
Joined: Tuesday 5 December 2006, 15:28
Location: sLOVEenia

Post by voodoo » Wednesday 28 February 2007, 20:58

The Blitz wrote:Yeah...Shoe Goo!
I would like to find it in France for my hockey skate, but unfortunately Shoe Goo is banned (toxic ?) :?
if you want i can send you a few of them...
boards:Swoard 175 H, Sigi Grabner Speed GS 185
bindings: F2 Race titanium, INTEC TITANFLEX
Boots: Deeluxe Indy+BTS,

User avatar
Ohawa
Rank 5
Rank 5
Posts: 192
Joined: Monday 23 January 2006, 13:44
Location: Neuchâtel
Contact:

Post by Ohawa » Friday 2 March 2007, 17:49

I use Duck tape on gloves and pants where cut by the edge. It is grey/silver but replacable after it gets worn... few years of satisfaction on leather gloves.
Board? Just a Choc, 180...

User avatar
Paia
Rank 3
Rank 3
Posts: 33
Joined: Wednesday 12 October 2005, 10:14
Location: Schio

Post by Paia » Tuesday 13 March 2007, 9:00

:idea: my solution:
Attachments
after.jpg
After
after.jpg (27.33 KiB) Viewed 11167 times
before.jpg
Before
before.jpg (24.4 KiB) Viewed 11167 times
Life is crash to crash
F2 Silberpfeil 162 + F2 Race titanium
F2 Silberpfeil 168 + F2 Race titanium
F2 Roadster 162
BURTON UFO 171 Tavola non ben identificata
NIDECKER Extreme 168
RAICHLE AF700
BURTON Wind

User avatar
The Blitz
Rank 5
Rank 5
Posts: 1532
Joined: Friday 4 October 2002, 13:59
Location: IdF | 91
Contact:

Post by The Blitz » Thursday 3 May 2007, 16:22

The Blitz wrote:
István wrote:The SikaLatex did not look too great for the first look. Shall I apply more layers?
I bought Sikalatex last week at Leroy Merlin (500ml, 7€).
It's look like milk when you apply it on jacket, but after 2 hours it's transparency.
:rules:
Look like SM (sky leather) when applie on my ass, but work well...
Attachments
P5030036.jpg
Sikalatex - 500ml
P5030036.jpg (124.89 KiB) Viewed 11148 times
 - 168XH Pro - Custom Dual 168H - Swallow Undertakeur 185

-- Tignes 19 au 25 mars --

User avatar
István
Rank 5
Rank 5
Posts: 899
Joined: Monday 29 September 2003, 13:04
Location: Budapest, Hungary

Post by István » Thursday 3 May 2007, 16:58

Guys, since then I have tested the Sikaflex 252 / SikaTack Drive on several parts of my gear and it works great. You'll see me next year in Zinal, I'll look like RubberMan ;-)


Ciao

User avatar
eaglefly
Rank 5
Rank 5
Posts: 597
Joined: Wednesday 10 November 2004, 14:46
Location: Idf/92 (France)

Post by eaglefly » Wednesday 3 October 2007, 8:04

Arnaud wrote:Personnally, I use leather pieces glued with neopren on gloves, arm.
4 seasons on gloves without problem. Leather is very very wear resistant.
I glued pieces of leather on my gloves cause there were small holes on the finger parts; I guess I didn't use the right glue (pattex colle puissante) because almost all pieces on my fingers were gone after a few hours of riding. I was also quite disappointed about the state of leather pieces still glued on my gloves...bad quality leather maybe :roll: anyway, I couldn't easily find polyglut neither other glue in China so I had no choice but I'll polyglut my gloves for the coming season I guess.
* * * "Carve diem, that's it " * * *

User avatar
István
Rank 5
Rank 5
Posts: 899
Joined: Monday 29 September 2003, 13:04
Location: Budapest, Hungary

Post by István » Wednesday 3 October 2007, 9:35

Celine, try to get something similar to the Sika products. Anything that they use to glue the windshields of cars should do. Those are black colour rubber based glues and should stick well to your clothes. China being a big car manufacturer should offer you a variety of these materials.

Once you get it, just apply 2-3 thin layers onto the worn parts. It will look like factory made.

Cheers

User avatar
chazwhite42
Rank 0
Rank 0
Posts: 3
Joined: Monday 4 February 2008, 18:06
Location: California USA
Contact:

Slide gloves

Post by chazwhite42 » Monday 4 February 2008, 23:37

I was carving with duct taped gloves with plastic milk bottles glued to the palms (ugly but they got the job done). Then by chance last month I ran across a pair of skate board slide gloves. They work really well. I simply wear a pair of under gloves and the slide gloves on top. I was worried that the pads might pull off during a turn, but so far they haven't (but Ive only used them a few times so far). I like them because I can put a bit more weight on them than I have on my home made gloves. Here is a link to their website

http://www.gravityboard.com/pages/gstor ... glove.html

User avatar
SITO
Rank 5
Rank 5
Posts: 237
Joined: Tuesday 20 May 2003, 17:39
Location: Spain

Post by SITO » Friday 15 February 2008, 15:09

Hi guys!

Yesterday I was repairing my holes on my gloves with Sikaflex, but how it seem to me that the surface created for Sikaflex over my gloves should not slide fine , I tried to glue a piece of P-TEX 200 over the palm of both gloves, after some hours waiting ,I checked how strong these pieces was glued and the result was negative , I was able easily remove the P-tex from both gloves, the Sikaflex don't work . (I think it's because of the flat surface of the P-TX )

How do you glue these pieces , or what product are you using to glue plastic, P-tex etc to the palm of your gloves??

S
Ride hard;100% fun

User avatar
István
Rank 5
Rank 5
Posts: 899
Joined: Monday 29 September 2003, 13:04
Location: Budapest, Hungary

Post by István » Friday 15 February 2008, 15:34

Sika Tack-drive.

Used in automotive industry to fix glasses. Black rubber like material when cured. Slides well enough. Resistant to wear. You can also use it to attach anything onto your gloves / pants / jackets, but I would say just prepare a nice layer on your gear and it will do.

You should be able to locate a dealer close to you on internet.


Cheers


http://www.sikaindustry.com/tds-ipd-sik ... agr-us.pdf

User avatar
SITO
Rank 5
Rank 5
Posts: 237
Joined: Tuesday 20 May 2003, 17:39
Location: Spain

Post by SITO » Friday 15 February 2008, 22:43

Thanks Istvan! :wink:
I'll try to get it, and I let you know how this product work.

S;
Ride hard;100% fun

Locked