binding angle question
Moderators: fivat, rilliet, Arnaud, nils
binding angle question
About two months ago I received my Swoard and I can hardly wait anymore to try it. On the Swoard, I’ve put a pair of F2 Race Titanium bindings.
Now I have a question regarding the degrees to use on the front and back binding. I’m asking you guys this, because I want to try the push-pull turns on my Swoard with a good degree setting on both bindings which suites me.
I really hope you guys can help me on this issue.
I'm 200cm tall and feet size is 45
I've been in contact with Nils and he thought around 50 degrees on the back and 5-7 more on the front. I've been testing with the angles and what Nils thought is what's on my board now.
The only thing that I'm not sure off: is the back binding in a good position now or should I rotate it a few degrees more?
Therefore I've attached an image of several images I made, so please advise, comment just for me to have a conformation that I’m on the right position on the board.
Now I have a question regarding the degrees to use on the front and back binding. I’m asking you guys this, because I want to try the push-pull turns on my Swoard with a good degree setting on both bindings which suites me.
I really hope you guys can help me on this issue.
I'm 200cm tall and feet size is 45
I've been in contact with Nils and he thought around 50 degrees on the back and 5-7 more on the front. I've been testing with the angles and what Nils thought is what's on my board now.
The only thing that I'm not sure off: is the back binding in a good position now or should I rotate it a few degrees more?
Therefore I've attached an image of several images I made, so please advise, comment just for me to have a conformation that I’m on the right position on the board.
- Attachments
-
- all.jpg (86.2 KiB) Viewed 14904 times
SWOARD EC Pro 175H + F2 Race Titanium + Head Stratos Pro with ACSS attached personally by Arnaud ;)
that's a bit of a problem you say, because I still haven't got the chance to try it on a normal piste
In the netherlands we have several indoor posibilities, but around these days they are way to crowded. Besides this the indoor facilities are to small
for a swoard
I'll be leaving for my holiday in 2,5 weeks and that's the first opportunity to try for me.
In the netherlands we have several indoor posibilities, but around these days they are way to crowded. Besides this the indoor facilities are to small
for a swoard
I'll be leaving for my holiday in 2,5 weeks and that's the first opportunity to try for me.
SWOARD EC Pro 175H + F2 Race Titanium + Head Stratos Pro with ACSS attached personally by Arnaud ;)
binding angle setting
Try to put the board on its side (with the shoes fixed on binding), and measure the angle between the base and the floor. It should not be less than 80°. Then put the board on the other side and verify if the angle is the same. Adjust the binding angle and enventually translate the binding forward / back to obtain the same base / floor angle on each side. 80-85° is a good value.
Swoard EC Pro2 168H - Swoard EC12 Boots - Gen5 168H - Stoke 162 M
Ik heb pas geleden ook m'n Swoard ontvangen en 'm inderdaad ook op z'n kant gelegd; de bindingen losjes op de swoard geschroefd en de schoen er in geklemd, vervolgens de schoenen&bindingen gedraaid tot deze de vloer niet meer raakten; ook kan je via de schroeven van je bindingen de schoenen naar voren of achteren verplaatsen/verstellen, maar ik heb ze in principe in 't midden staan; er staan wat streepjes waar je kan zien hoe ver de voorbeugel staat ten opzichte van de achterbeugel.
Hoop je te hebben geholpen, Eric
Hoop je te hebben geholpen, Eric
Swoard Pro2 175M, Redline bindings, UPZ RC10
eric, je zet hem dan op zijn kant tegen de muur aan neem ik aan?
de schroeven van de bindingen heb ik al afgesteld op mijn schoenen ja, en die heb ik ook in het midden staan
(best grappig, want ik zie France-Avignon onder je avatar staan en dan verwacht je niet dat die persoon in het nederlands gaat antwoorden )
de schroeven van de bindingen heb ik al afgesteld op mijn schoenen ja, en die heb ik ook in het midden staan
(best grappig, want ik zie France-Avignon onder je avatar staan en dan verwacht je niet dat die persoon in het nederlands gaat antwoorden )
SWOARD EC Pro 175H + F2 Race Titanium + Head Stratos Pro with ACSS attached personally by Arnaud ;)
'k ben met een française getrouwd, vandaar !!....als de schoenen aan je board zijn geklipst, kun je in feite 't board op z'n kant leggen zonder dat 't board tegen een muur moet liggen, want de schoenen voorkomen dat 't board omvald, dan ga je 'n meter achter of voor je board liggen en kijk je of je schoenen de grond raken, dat doe je voor front_ en backside en regel je tot je schoenen nergens meer uitsteken....dan moet 't goed zitten en kun je liggende bochten gaan draaien...succes, Eric
Swoard Pro2 175M, Redline bindings, UPZ RC10
Effe wat anders...misschien vind je dit leuk ?...Hans had 't logo bij de http://www.thestitch.nl in Vlaardingen laten maken en met Pasen 2006 heb ik voor 16 euros/jas dit erop laten stikken.
- Attachments
-
- swoard003.jpg (31.32 KiB) Viewed 14761 times
-
- swoard_002.jpg (27.97 KiB) Viewed 14761 times
-
- swoard_001.jpg (27.23 KiB) Viewed 14761 times
Swoard Pro2 175M, Redline bindings, UPZ RC10